Invacare Hydra C650PW страница 120 Скачать руководство пользователя | Manualshive

Страница: 120 / 126

background image

Chapter 7 : Appendices

33

The Shark programming adapter is intended to allow the Shark Controller series of
power wheelchair controllers to communicate with the DX Hand Held Programmer
and the SHARK Support Tool. The adapter is not intended to alter the controller in
any way, but simply passes information to and from the controller. The information
passed may alter the controller performance.

The intended power source is a 24V battery supply from the Shark controller. The
intended environment is indoors, or outdoors in dry conditions.

«
...
118
119
120
121
122
...
»

Содержание Hydra C650PW































































































































Отзывы:

Нет отзывов

Похожие инструкции для Hydra C650PW

Бренд: Sunrise Medical Страницы: 96

Electric wheelchair

Бренд: Invacare Страницы: 97

Бренд: Roma Medical Страницы: 46

Бренд: Electra Страницы: 63

Бренд: Küschall Страницы: 44

Бренд: Küschall Страницы: 116

Бренд: Stryker Страницы: 159

Бренд: Rehab and Mobility Products Страницы: 4

Бренд: BCP Страницы: 8

Quick Release Amputee Support

Бренд: Comfort Company Страницы: 2

Бренд: R82 Страницы: 6

Бренд: Q'STRAINT Страницы: 4

Бренд: Vicair Страницы: 94

Compact Featherlight 757

Бренд: Tuffcare Страницы: 16

UniLink Elbow Arm Pad Stop

Бренд: Stealth Products Страницы: 16

Бренд: Stealth Products Страницы: 16

FOLD & GO WHEELCHAIR

Бренд: OneKubedDESIGNS Страницы: 10

E-Traveller 180

Бренд: Motobility Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды