Invacare Hydra C650PW страница 104 Скачать руководство пользователя | Manualshive

Страница: 104 / 126

background image

Chapter 5 : Diagnostics

17

4

Programming the DK-PMA

Performance adjustments should only be made by professionals in the
health care field or by persons fully conversant with the adjustment
process and the operator’s capabilities. Incorrect settings or
programming in an unsafe location could cause injury to the operator or
bystanders, or damage to the vehicle or surrounding property.

After the vehicle has been configured, check to make sure the vehicle
performs to the specifications entered in the programming procedure. If
the vehicle does not perform to specifications, reprogram it. Repeat this
procedure until the vehicle performs to specifications. If the intended
operation cannot be achieved, contact your service agent.

4.1 Introduction

SHARK is fully programmable to provide superb performance for a wide
variety of powerchair configurations and users. All programmed values are
stored in the Power Module. In the event that the Control Unit is replaced,
there is no need to reprogram SHARK. If the Power Module is replaced,
SHARK can simply be reprogrammed with an identical powerchair program.

4.2

DK-PMA Programmable Parameter Descriptions

Setting

Description

Active Drive Program

Defines which of the three available Drive Programs is to be
used. If set to DCI Select 1+2, the DCI Swivel function will
change to a Drive Program Swap mode. Activation of the
DCI Swivel function will change the Active Drive Program
from Drive Program 1 to 2.

DCI Operation

Defines if the DCI is Off, Normally Open or Normally
Closed. See Section 3.2.6 – Drive Control Input (DCI)
Connections.

DCI Speed Limit

Sets the maximum speed that SHARK will drive at when the
DCI Speed Limit function is active.

Emergency
Deceleration

Defines the deceleration rate that SHARK will use when a
fault is detected.

«
...
102
103
104
105
106
...
»

Содержание Hydra C650PW































































































































Отзывы:

Нет отзывов

Похожие инструкции для Hydra C650PW

Бренд: Decon wheel Страницы: 4

Бренд: progeo Страницы: 56

Atmos ultra CL200 38 Series

Бренд: ARDEA ONE Страницы: 60

Бренд: CareCo Страницы: 11

Бренд: Making Life Easy Страницы: 8

ROHO Smart Check

Бренд: Permobil Страницы: 2

ROHO AGILITY CARBON

Бренд: Permobil Страницы: 20

Бренд: Permobil Страницы: 40

Бренд: Permobil Страницы: 46

Бренд: Permobil Страницы: 60

Compass Power Mount

Бренд: Permobil Страницы: 60

Comfort M2 BodiLink LPTS

Бренд: Permobil Страницы: 64

Бренд: AAT Страницы: 80

Бренд: identités Страницы: 10

Бренд: Nova Страницы: 3

Бренд: Life & Mobility Страницы: 67

Бренд: Ferno Страницы: 21

Бренд: Ferno Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды