Invacare Formula CG Elevate Скачать руководство пользователя страница 47

Страница: 47 / 95

Usage

6.11

Raising/Lowering Elevating Front Riggings

Perform one of the following:

•

Raising - Pull back on the release lever

and raise front

rigging to the desired height.

•

Lowering - Support front rigging with one hand away from
the release lever. Push release lever downward with other
hand.

6.12

Adjusting Calfpads

Rotate the calfpad

towards outside of the wheelchair.

Slide the calfpad up or down until the desired position is obtained.

If one of the top two calf pad adjustment positions is
being used, the legrest will need to be raised to avoid
interference with the front stabilizers while going over
obstacles or going up and down ramps.

Rotate the calfpad towards the inside of the wheelchair.

1143155-R-01

Содержание Formula CG Elevate
































































































Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды

Invacare Formula CG Elevate, Руководство пользователя

Результаты поиска

Содержание Formula CG Elevate

Отзывы:

Похожие инструкции для Formula CG Elevate

Бренды по названию

Популярные бренды