background image

Invacare® Formula™ CG Seating

6.9.2

CMPJ+ Joystick

The far right side of the display screen

A

is the Battery Gauge Display

B

. It provides information on the remaining charge in the batteries.

At full charge, solid blocks fill in battery gauge. As the battery
becomes discharged, the segments will progressively disappear
starting on the right and moving towards the left a bar at a time
until no segments appear. At this level the user should charge the
batteries as soon as possible.

6.10

About Front Riggings

WARNING!
Risk of Serious Injury or Damage

Operating the wheelchair with a ground clearance of
less than 75 mm (3 inches) between the footplates and
the ground/floor may cause serious injury or property
damage.

ALWAYS maintain a minimum of 75 mm (3

inches) between the bottom of the footplates and
ground/floor to ensure proper ground clearance while
the wheelchair is in motion. If necessary, adjust the
footplates height to achieve proper ground clearance.
After footplates height adjustment, if the wheelchair
dips forward and the footplates touch the ground
while in motion, please contact your dealer for an
inspection and avoid use of the wheelchair if possible.

If the wheelchair is not moving, the front rigging must
maintain a minimum of one inch ground clearance -
otherwise personal injury and damage may result.

WARNING!

PINCH POINT EXISTS BETWEEN CENTER MOUNT

FOOTREST AND CASTERS - There is limited
clearance between center mount footrest and casters.
The user’s feet MUST remain on the center mount
footrest while operating the wheelchair. If the user’s
feet are allowed to rest off the side of the center
mount footrest they may come in contact with the
caster possibly resulting in injury.

46

1143155-R-01

Содержание Formula CG Elevate
































































































Отзывы: