Invacare Carroll CS Series Скачать руководство пользователя страница 54

Страница: 54 / 60

Invacare® Carroll CS Series™

7 Maintenance

7.1 Cleaning

WARNING!
Risk of Injury or Damage

To avoid injury or damage from misuse:

– Read all guidelines, warnings and cautions

before performing any repair/maintenance on
the bed.

– All repair and maintenance on the bed should

be performed by a qualified technician.

DANGER!
Risk of Death, Injury or Damage

To avoid damage to electric controls:

– If a liquid is spilled in or around the electric

bed, unplug the electric bed before cleaning.

– Clean up the spill and allow the electric bed

or the area around the electric bed to dry
thoroughly before using the electric controls
again.

WARNING!
Risk of Injury or Damage

Grease may leak from the gearbox and cause
injury or damage from falling or fire.

– Follow the maintenance instructions in this

manual.

– Routinely inspect the gearbox for grease

leakage.

If the gearbox is leaking grease:

– Stop use immediately.
– Keep the product away from sparks, flame and

open heat sources.

– Contact your dealer or Invacare for repair.

WARNING!
Risk of Injury or Damage

The electric motors, control box and pendant
are NOT protected against the entrance of dust
and liquids.

– DO NOT spray liquids into any electrical

components.

– DO NOT wash head or foot section.
– DO NOT allow electrical components to get wet.

WARNING!
Risk of Injury or Damage

To avoid product damage or injury from
malfunction:

– Clean the product according to the instructions.
– The product may be damaged from multiple

or excessive cleaning.

1153410-Q

Содержание Carroll CS Series





























































Результаты поиска

Содержание Carroll CS Series

Отзывы:

Бренды по названию

Популярные бренды

Invacare Carroll CS Series, Руководство пользователя

Результаты поиска

Содержание Carroll CS Series

Отзывы:

Бренды по названию

Популярные бренды