manualshive.com logo in svg

Invacare Carroll CS Series, Руководство пользователя

Поделиться
Скачать
Invacare Carroll CS Series Скачать руководство пользователя страница 25

Safety

3.3 Electromagnetic Compatibility Information

Portable and mobile RF communications equipment
can affect medical electrical equipment.

WARNING!
Risk of Product Damage

The use of accessories, transducers, cords
and cables other than those specified by the
manufacturer, may result in increased emissions
or decreased immunity of this bed.

– This product should not be used adjacent to or

stacked with other equipment. If adjacent or
stacked use is necessary, this product should
be observed to verify normal operation in the
configuration in which it will be used.

3.4 Disposal

Follow local governing ordinances and recycling plans
regarding disposal of the product or components normally
used in operation. The product does not generate waste
or residue in operation. Any accessories not part of the
product MUST be handled in accordance with the individual
product marking for disposal.

This product has been supplied from an environmentally
aware manufacturer that complies with the Waste Electrical
and Electronic Equipment (WEEE) Directive 2012/19/EC.

This product may contain substances that could be harmful
to the environment if disposed of in places (landfills) that
are not appropriate according to legislation.

Please be environmentally responsible and recycle this
product through your recycling facility at its end of life.

1153410-Q

25

Содержание Carroll CS Series





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды