background image

Setup

Adjusting Width

Fig. 4-3 Seat frame of models without tilt- or lifter-tilt modules

Fig. 4-4 Seat frame of models with tilt- or lifter-tilt modules

1.

Loosen and remove screws

A

.

2.

Loosen and remove screws

B

and nuts

C

.

3.

If required, replace legrest fixation

D

.

4.

Adjust seat rail connector and legrest fixation to desired
seat width according to table:

Screw Position

Seat Width

F

380 mm

G

430 mm

H

480 mm

I

530 mm

J

550 mm (optional)

Fig. 4-5 Mounting positions for

different seat widths on seat rail

connector

E

. Variant on model

without tilt- or lifter-tilt module

serves as example.

Fig. 4-6 Mounting positions for

different seat widths on legrest

fixations

D

.

Installing Parts

1.

Install parts in reverse order.

2.

Test all functions.

4.1.2 Adjusting Backrest Width

The backrest width of 550 mm cannot be retrofitted. Contact Invacare for more information.

Backrest width is adjusted by performing the following tasks:

1.

Adjusting backrest posts.

2.

Adjusting backrest.
a. Tension-adjustable backrest: See

4.1.3 Adjusting Tension-Adjustable Backrest, page 10

.

b. Flex3 backrest: See

4.1.4 Adjusting Flex3 Backrest, page 10

.

3.

Replacing backrest cushion (these are available in various widths).
When modifying backrest width, seat width must also be correspondingly adapted. See

4.1.1 Adjusting Seat Width,

page 8

.

3 mm Allen key

5 mm Allen key

13 mm wrench

For screw position per backrest width, refer to table below.

Fig. 4-7 Upper actuator fixation bracket.

Fig. 4-8 Lower actuator fixation bracket.

1604311-G

9

Содержание AVIVA RX40













































Отзывы: