background image

Part No 1046525

1

Back Cane Replacement Kits for 9000 Series 

For more information regarding Invacare products, parts, and services, 

please visit www.invacare.com

Back Cane Replacement Kits
for 9000 Series Wheelchairs

Kit Nos. 1048919, 1048920, 1048921, and 1048922

NOTE:

 

These

 

instructions

 

apply

 

to

 

the

 

9000

 

XT/XDT

 

and

 

the

 

9000

 

SL

 

with

 

adjustable

 

back

 

angle

 

option.

NOTE:

 

Check

 

all

 

parts

 

for

 

shipping

 

damage.

 

In

 

case

 

of

 

damage,

 

DO

 

NOT

 

use.

 

Contact

 

Carrier/Invacare

 

for

 

further

 

instructions.

Safety Summary

 

WARNING

DO NOT install this equipment without first reading and understanding this 

instruction sheet. If you are unable to understand the warnings, cautions and 

instructions, contact a healthcare professional, dealer or technical personnel 

if applicable, before attempting to install this equipment - otherwise, injury or 

damage may occur.
Invacare products are specifically designed and manufactured for use in 

conjunction with Invacare accessories. Accessories designed by other 

manufacturers have not been tested by Invacare and are not recommended 

for use with Invacare products.
After ANY adjustments, repair or service and BEFORE use, make sure that 

all attaching component parts are secure.

NOTE:

 

For

 

this

 

procedure,

 

refer

 

to

 

FIGURE 1.

1. Remove

 

the

 

two

 

mounting

 

screws

 

and

 

washers

 

that

 

secure

 

the

 

back

 

upholstery

 

to

 

the

 

back

 

canes

 

(Detail

 

“A”).

2. Remove

 

the

 

two

 

mounting

 

screws,

 

locknuts,

 

and

 

(for

 

wheelchairs

 

manufactured

 

after

 

11/1/2005)

 

spacers

 

that

 

secure

 

one

 

back

 

cane

 

to

 

the

 

wheelchair

 

frame

 

(Detail

 

“C”).

3. Pull

 

the

 

loose

 

back

 

cane

 

out

 

of

 

the

 

back

 

upholstery.

4. Slide

 

a

 

new

 

back

 

cane

 

through

 

the

 

back

 

upholstery.

5. Secure

 

the

 

new

 

back

 

cane

 

to

 

the

 

wheelchair

 

frame

 

at

 

the

 

desired

 

back

 

height

 

with

 

the

 

two

 

mounting

 

screws,

 

locknuts,

 

and

 

(for

 

wheelchairs

 

manufactured

 

after

 

11/1/2005)

 

spacers

 

(Detail

 

“B”).

NOTE:

 

For

 

wheelchairs

 

manufactured

 

after

 

11/1/2005,

 

the

 

spacers

 

must

 

be

 

on

 

the

 

outside

 

of

 

the

 

wheelchair

 

in

 

order

 

for

 

the

 

mounting

 

screws

 

to

 

be

 

properly

 

tightened

 

(Detail

 

“C”).

Assembly, Installation and Operating Instructions

SAVE THESE INSTRUCTIONS

Отзывы: