Interroll ZoneControl Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 54

background image

Version 2.0 (04/2019) Online

Translation of the original operating manual

13 von 54

Safety-related information

2.6

Interface to other devices

The integration of the ZoneControl into a conveyor system can create additional potential hazards. Such potential

hazards are not covered by this operating manual and must be analysed during the development, installation and

commissioning of the conveyor system as a whole.

¾

Following the integration of the ZoneControl into a conveyor system, the entire system must be checked for any

new potential hazards that may be present before the conveyor is switched on.

2.7

Operating modes/operating phases

Standard operation

Operation in the installed condition at the end customer as a component in a conveyor in an overall system.

Special operation

Special operation encompasses all operating modes/operating phases that are necessary to guarantee and maintain

safe standard operation.

Special operating mode

Comments

Transport/storage

-

Assembly/commissioning

In de-energised state

Cleaning

In de-energised state

Maintenance/repair

In de-energised state

Fault location

-

Troubleshooting

In de-energised state

Decommissioning

In de-energised state

Disposal

-

«
...
11
12
13
14
15
...
»

Содержание ZoneControl























































Отзывы:

Нет отзывов

Похожие инструкции для ZoneControl

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 40

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: UNITED Страницы: 8

Бренд: Accu-Sort Страницы: 22

Бренд: Febco Страницы: 12

Бренд: HANYOUNG NUX Страницы: 36

Бренд: HANYOUNG NUX Страницы: 4

Бренд: MADRIX Страницы: 91

Бренд: MADRIX Страницы: 36

Бренд: MADRIX Страницы: 40

Бренд: YASKAWA Страницы: 18

Бренд: jbc Страницы: 44

Бренд: jbc Страницы: 8

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Compact Comfort VAV12

Бренд: SAI HVAC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды