Interroll ZoneControl Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 54

background image

10 von 54

Version 2.0 (04/2019) Online

Translation of the original operating manual

Safety-related information

2

Safety-related information

2.1

State of the art

The Interroll ZoneControl has been constructed with respect to applicable standards and the current state of the art

and has been delivered in a condition that is safe to operate. Nevertheless, hazards can occur as a result of use.

Non-compliance with the instructions in this operating manual can result in life-threatening injuries.

In addition, the applicable local accident prevention regulations for the area of application and general safety

regulations must be adhered to.

2.2

Proper use

The ZoneControl may only be used in an industrial environment for industrial purposes within the stipulated

performance limits that are given in the technical specifications.
It controls an Interroll RollerDrive and must be integrated into a conveyor unit or conveyor system before

commissioning.

2.3

Improper use

Any use that goes beyond the proper use is considered improper, unless this has been authorised by Interroll

Engineering GmbH where applicable.
The equipment must not be installed in areas in which substances could form explosive atmospheres/dust atmospheres

or for application in the medical/pharmaceutical sector.
It is considered improper use to install the equipment in exposed spaces that are open to potentially adverse weather

conditions, or areas in which the technology would suffer from the prevailing climactic conditions and could potentially

malfunction as a result.
The ZoneControl is not intended for use by private end users. The equipment must not be used in a residential

environment without further examination and without the use of EMC protective measures that have been adapted

accordingly.
It must not be used as a safety-relevant component or for performing safety-relevant functions.

«
...
8
9
10
11
12
...
»

Содержание ZoneControl























































Отзывы:

Нет отзывов

Похожие инструкции для ZoneControl

Бренд: jbc Страницы: 4

Бренд: TCS Basys Controls Страницы: 2

PROFINET BNI PNT-508-055-P067

Бренд: Balluff Страницы: 84

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Barco Страницы: 6

Бренд: Barco Страницы: 4

Бренд: Harmonic Drive Страницы: 25

Бренд: Nelson Страницы: 8

Бренд: Faulhaber Страницы: 66

Бренд: X Rocker Страницы: 38

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Fox Страницы: 5

CWDM-CR-B Series

Бренд: Lantronix Страницы: 19

Бренд: Netafim Страницы: 4

Бренд: TREND Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды