Interlogix IFS MC250-4T Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 23

background image

IFS MC250-4T/XXX Series User Manual 7

1 2 3 4 5 6

Note:

The wire gauge for the terminal block should be in the

range between 12 ~ 24 AWG.

The alarm relay circuit accepts up to 30V, max. 3A currents.

Mounting Installation

This section describes how to mount the MC250-4T and make
connections to it. Please read the following sections and
perform the procedures in the order presented.

Note:

In the installation steps below, this Manual uses the IFS

8 Port Industrial Gigabit Switch, GE-DSGH-8, as an example.
However, the steps for any IFS Industrial Switch & Industrial
Media Converter are similar.

Insert the wires into the fault alarm contacts

«
...
9
10
11
12
13
...
»

Содержание IFS MC250-4T Series
























Отзывы:

Нет отзывов

Похожие инструкции для IFS MC250-4T Series

Бренд: D-Link Страницы: 6

Бренд: R volution Страницы: 24

LIMETREE USB-DAC

Бренд: Lindemann Страницы: 24

Бренд: IRiver Страницы: 33

Бренд: ICP DAS USA Страницы: 43

Бренд: ICP DAS USA Страницы: 3

Бренд: AV Link Страницы: 2

Бренд: Metra Electronics Страницы: 9

Бренд: Growatt Страницы: 25

EASI ATM IND2x2 Series

Бренд: Teleste Страницы: 28

Бренд: Parker Страницы: 172

Video Sweep Generator MVG 10

Бренд: Kathrein Страницы: 28

10/100Base-TX to 100Base-FX

Бренд: Microsens Страницы: 13

Бренд: Phrontier Technologies Страницы: 16

Бренд: Sveon Страницы: 45

PWRIG100012120S

Бренд: AIMS Power Страницы: 16

Бренд: Lindy Страницы: 12

Бренд: AMS Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды