Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 285

Страница: 285 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

279

The SMS reports and unrecognized SMS commands have two separate

counters. However, the maximum limit defined in this menu is the same for both

counters.
There is no limit for messages if this value is set to 0.

9.3.n.6.4 SMS header msg

4 SMS header msg
> <

The SMS header message identifies the Advisor Advanced system. It is included

at the beginning of each text SMS message sent by the system, if the reporting

format is set to SMS text. See “9.1.n.3 Protocol” on page 259

9.3.n.6.5 User PIN req.

5 User PIN req.
>No<

If the User PIN required option is set to Yes, you must start every SMS control

message with your PIN, otherwise the command will be rejected. See the

Advisor

Advanced SMS Control Reference Manual

for more information.

9.3.n.6.6 Ext.charset

6 Ext.charset
>No<

The Extended charset (UCS2) option has an influence on the SMS messages

sent by the Advisor Advanced system to the user. This option must be set to Yes

prior to read SMS reports and responses with special and national characters

that exceed the standard GSM charset GSM3.38.

Notes

• The extended charset is used only if there is no possibility to send the

message in the standard charset.

• Older cell phones may not correctly display messages that use the extended

charset.

9.3.n.7 GPRS Setup

1 APN
None

The

GPRS Setup menu lets you change various GPRS settings.

9.3.n.7.1 APN

1 APN
> <

The

Access Point Name is a configurable network identifier used by a mobile

device when connecting to a GSM carrier. It must be specified by the GPRS

provider.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию, Страница: 285 / 376

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы: