Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 281

Страница: 281 / 376

Chapter 5: Menu reference

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

275

the system automatically selects another network, if the configured network is

unavailable.

9.3.n.5.2.3 Net.scanning

0>Rescan nets
1 * MyGSM

The Network scanning menu lists all available networks. It also lets you force

another scan.
The list contains GSM network names that are preceded by one of the following

marks that define the network availability:
• *: The network is currently connected.

• +: The network is allowed for connection.

• -: The network is forbidden for connection.
If the network name is unknown (not recognized by the GSM dialler), the network

code in square brackets is displayed instead of the name, for example,

“+ [20999]”.

9.3.n.5.2.3.0 Rescan nets

Scan in progress
Please wait

The Rescan nets command performs a GSM network scan.
The scan can take a few minutes. You can cancel the scan by pressing Clear.

9.3.n.5.2.3.m Select a network

1>Network name
MyGSM

Select a network to see more options.

9.3.n.5.2.3.m.1 Network name

1>Network name
MyGSM

The Network name is the name of the GSM network. Refer to “1.2.8.6 Network

name” on page 134 for more details.

9.3.n.5.2.3.m.2 Network code

2>Network code
21999

The Network code is the unique code of the GSM network. Refer to “1.2.8.7

Network code” on page 134 for more details.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды