Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 264

Страница: 264 / 376

Chapter 5: Menu reference

258

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

9 Dialler menu

1>CS
2 Event options

The menu is used to program all system-wide communication options.

9.1 Central station

0>Add CS
1 CS 1

The Advisor Advanced system lets you program up to 16 central stations.

9.1.0 Add CS

Access the menu to add a central station.
If the central station is created successfully, the following message appears:

INFO
CS added

The new central station is given the default name “CS N” and placed on the end

of the central station list.
You can now start editing the central station details for the new central station.

9.1.n Select central station

01>CS name
CS 1

Select a central station to program.

Note:

Particular options in this menu differ for specific transmission paths. For

specific options, see:
• “PSTN and ISDN specific options” on page 263

• “IP and GSM/GPRS specific options” on page 263

• “Photo transmission specific options” on page 265

• “GSM/phone specific options” on page 265

Common options

9.1.n.1 CS name

1 CS name
>CS 1 <

Use the CS name screen to enter or change the central station name. Central

station name can consist of up to 16 characters.

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды