Intergraph Zx10 Ultra-Tower Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 100

background image

75

SCSI Cabling

SCSI cabling in the system is as follows:

♦

A SCSI cable connects Channel A of the on-board SCSI controller to the external port on the
back of the base unit and, in some systems, to front-access SCSI devices. Either the external-
only or the internal/external cable is used, but not both.

WARNING

For continued protection against fire and energy hazards, do not connect an
external SCSI port to SCSI Channel B. Connect an external SCSI port only to
SCSI Channel A.

♦

A cable connects Channel B of the on-board SCSI controller to up to three SCSI disk drives.

Cable connects SCSI Channel B to
three SCSI disk drives

Internal/external cable connects
SCSI Channel A to two front-access
SCSI devices and to port above
power supply; port is terminated
with an external terminator module

External-only cable connects SCSI
Channel A to port below rear fan;
port is not terminated

External SCSI port location on back
of base unit is based on which SCSI
cable is used

«
...
85
86
87
88
89
...
»

Содержание Zx10 Ultra-Tower





































































































Отзывы:

Нет отзывов

Похожие инструкции для Zx10 Ultra-Tower

Бренд: Safco Страницы: 2

Бренд: Acer Страницы: 26

Бренд: EBN Страницы: 9

Бренд: SeaLevel Страницы: 40

PC 300GL Type 6267

Бренд: IBM Страницы: 58

Бренд: Technologic Systems Страницы: 38

Бренд: Gateway Страницы: 176

Бренд: IEI Technology Страницы: 121

Бренд: Advantech Страницы: 68

Бренд: Lenze Страницы: 68

Бренд: Contec Страницы: 116

Бренд: Corsair Страницы: 16

Бренд: Shuttle Страницы: 38

Бренд: Shuttle Страницы: 73

C5m/F5m CFT-004

Бренд: Motion Страницы: 76

Бренд: Alpha Microsystems Страницы: 110

Altos BrainSphere P10 F7 SFF

Бренд: Acer Страницы: 40

TitraLab KF1121

Бренд: Hach Страницы: 510

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды