Intergraph Zx10 Ultra-Tower Скачать руководство пользователя страница 68

Страница: 68 / 100

Floppy Disk Drive

The floppy disk drive occupies the lowest front-access device bay.

To replace the floppy disk drive:

WARNING

The system is always on when connected to AC power. Before performing this
task, disconnect the system’s power cord from its AC power outlet.

Disconnect the power and data cables from the drive.

Remove and retain the screws securing the floppy disk drive to its bay (left side only).

Slide the drive out the front of the base unit chassis.

Slide the new drive into the base unit chassis from the front.

Connect the data and power cables to the new drive.

Secure the new drive to its bay with the screws removed previously.

Floppy Disk Drive

Power and Data
Cables

Device Screws
(both sides)

Содержание Zx10 Ultra-Tower





































































































Результаты поиска

Содержание Zx10 Ultra-Tower

Отзывы:

Похожие инструкции для Zx10 Ultra-Tower

Бренды по названию

Популярные бренды

Intergraph Zx10 Ultra-Tower, Системное руководство

Результаты поиска

Содержание Zx10 Ultra-Tower

Отзывы:

Похожие инструкции для Zx10 Ultra-Tower

Бренды по названию

Популярные бренды