Intergraph Zx10 Ultra-Tower Скачать руководство пользователя страница 47

Страница: 47 / 100

Network

Cannot connect to other systems on LAN

Reason

Solution

Ethernet cable is disconnected.

Verify the Ethernet cable is connected. If the cable is
properly connected, notify your network administrator.

Networking software is configured
incorrectly.

Review the network settings in the operating system, and/or
notify your network administrator.

Cannot plot to network printer or plotter on LAN

Reason

Solution

Network cable is disconnected.

Verify the network cable is connected.

Printer or plotter is not added to your system.

Add the printer using the operating system tools,
and/or notify your network administrator.

Plot node does not recognize your system.

Notify your network administrator.

Peripheral Drive Errors

CD-ROM drive LED does not light when system power is on

Reason

Solution

Power cable or data cable is not connected.

Open the base unit and ensure the power cable
and data cable are properly connected.

Floppy disk drive LED does not light when system power is on

Reason

Solution

Power cable or data cable is not connected.

Open the base unit and ensure the power cable and
data cable are properly connected.

Miscellaneous Hardware

“Battery voltage low” message displays

Reason

Solution

Lithium battery voltage on the system board
is low.

Replace the lithium battery on the system board.

Содержание Zx10 Ultra-Tower





































































































Результаты поиска

Содержание Zx10 Ultra-Tower

Отзывы:

Похожие инструкции для Zx10 Ultra-Tower

Бренды по названию

Популярные бренды

Intergraph Zx10 Ultra-Tower, Системное руководство

Результаты поиска

Содержание Zx10 Ultra-Tower

Отзывы:

Похожие инструкции для Zx10 Ultra-Tower

Бренды по названию

Популярные бренды