Intellijel Steppy 3U Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 37

Intellijel Steppy 3U Скачать руководство пользователя страница 11

/

Steppy 3U Manual

●

RUN Mode

: This is an optional mode, into which you must boot Steppy (see

below).   As   with   RESET   Mode,   a   gate   received   at   the   RST   jack   resets   all   patterns
(across   all   four   tracks)   back   to   their   first   step,   but   it   also   enables   pattern
playback.   Specifically,   when   a   gate   is   high,
the   patterns   play.   When   a   gate   is   low,   they
don’t.   This   let’s   your   remotely   start   and   stop
patterns,   rather   than   having   them   run
continuously.

Hold the

SAVE

RST

button on boot up to toggle

between   RUN   and   RESET   modes   (the   setting   is
saved   across   boots).   On   the   SELECT   page,   you'll
see   the

SAVE

RST

button light

yellow

if RUN mode

is enabled.

Controls

1. MULTIFUNCTION Buttons

- These backlit button

perform different functions depending on Steppy’s
current mode.

●

Play Mode

: In Play Mode, the buttons set

and display gate patterns.

Play Mode is indicated when neither the
yellow Select Mode LED

[2]

nor the red Edit

Mode LED

[3]

is lit. You can also tell you’re

in Play Mode because (in general) the
majority of lit MULTIFUNCTION buttons are

GREEN

. See

for detailed

information.

Sixteen   steps   are   displayed   at   one   time,
with   steps   1-8   running   from   top-to-bottom
on   the   left   column,   and   steps   9-16   running
from   top-to-bottom   on   the   right   column.
Patterns   can   be   up   to   64   steps   long   (spread
across   4   pages);   and   four   entirely   different   patterns   can   exist   simultaneously   (in
Tracks A-D).

A

GREEN

button indicates that a step is ‘on’ (meaning it will send a gate to the

corresponding output). A flashing

GREEN

button indicates the last step in a

Page 10

«
...
9
10
11
12
13
...
»

Содержание Steppy 3U






































Отзывы:

Нет отзывов