IntelligentAg Engage Zone Control Скачать руководство пользователя

Страница: 6 / 8

1810 NDSU Research Circle N

Fargo, ND 58102

www.intelligentag.com

Page 6 of 8

Plug all connections of the motor controller harness back into their respective connections.
Refer to the motor controller harness connections diagram at the end of the maintenance
manual.

NOTE:

Ensure that that harness is routed toward the back of the enclosure.

Place the lid back on the enclosure, and latch the lid.

Plug the bin harness into the Engage® Zone Control unit enclosure.

Cycle the gates open and closed through the tractor’s virtual terminal.

Contact

Questions? Contact Intelligent Ag product support:

Canadian Product Support: 1-306-993-1156
United States Product Support: 1-701-436-1219

Or, email us at

[email protected]

Содержание Engage Zone Control









Результаты поиска

Содержание Engage Zone Control

Отзывы:

Похожие инструкции для Engage Zone Control

Бренды по названию

Популярные бренды

IntelligentAg Engage Zone Control, Информационное уведомление

Результаты поиска

Содержание Engage Zone Control

Отзывы:

Похожие инструкции для Engage Zone Control

Бренды по названию

Популярные бренды