background image

LSU220A : Load Support Unit

Operators Manual

Table of Contents

 1 MANUAL REVISION HISTORY....................................................................................................3
 2 DESCRIPTION..........................................................................................................................4
 3 INSTALLATION.........................................................................................................................5

 3.1 POSITIONING THE EQUIPMENT..........................................................................................5
 3.2 CONTROLS AND INDICATORS............................................................................................6

 3.2.1 Front panel.................................................................................................................6
 3.2.2 Rear panel..................................................................................................................7

 4 OPERATION.............................................................................................................................8
 5 CALIBRATION.........................................................................................................................10

 5.1 CHECKING PROCEDURE...................................................................................................11

 5.1.1 Voltage validation......................................................................................................11
 5.1.2 Current validation......................................................................................................12

 5.2 ADJUSTMENT PROCEDURE...............................................................................................12

 5.2.1 Voltage adjustment...................................................................................................12
 5.2.2 Current adjustment...................................................................................................12

 6 SPECIFICATIONS....................................................................................................................14
 7 PRODUCT DISPOSAL INSTRUCTIONS.......................................................................................15
 8 PRODUCT WARRANTY.............................................................................................................16

Doc: DWG1063-08-R2 LSU220A Operators Manual.odt

Page 2 of 16

Copyright Material of Intelligent Charging Limited © 2018

Printed On : 17/07/19

Содержание LSU220A

















Отзывы: