Intelligen INS-1500 Скачать руководство пользователя страница 15

Страница: 15 / 57

INS-1500 & INS-2000 • 5403646 • REV F • 04/19

Fig. 15

15.

Pipe the provided 10' of 3/8” drain tubing on the nitrogen cabinet to the floor drain in the sprinkler room. Do not pipe the

drain tubing upward. See Fig 15.

Drain Tube

CAUTION

Restrain all drain tubing.

16. Each riser requires a minimum of ONE Nitrogen Purge Valve to be installed prior to implementing the Nitrogen Purging

Procedure. For installation instructions, refer to Model NGP-SPV Bulletin (#5401520) or Model INS-PV Manual

(#5401532) supplied with each purge valve. See Fig. 7 for NGP-SPV installation diagram. See Fig. 8 for INS-PV installation

diagram.

Installing the purge valve upside down will not allow the system to purge. Also, ensure that there is NO water in

the pipe to the purge valve.

1/2" NPT TEE CONNECTION AND CLOSE NIPPLE
(SUPPLIED BY SPRINKLER CONTRACTOR)

PIPE FROM SPRINKLER SYSTEM

INSPECTOR'S TEST VALVE

PURGE ORIFICE (N

SAMPLING PORT)

NGP-SPV

PIPE PLUG (INSTALL AFTER
PURGE COMPLETE)
REMOVE PLUG WHEN SAMPLING
N

LEVELS AND PURGING

PURGE BALL VALVE
SHOWN IN NON - PURGE POSITION

UNION - POSITION VENT / ORIFICE
APPROPRIATELY

DWG. #0400-13

Fig. 16

7 1/4"

20 1/2"

7 1/8"

INSPECTORS TEST VALVE

PIPE FROM SPRINKLER SYSTEM

1/2" NPT TEE CONNECTION AND CLOSE NIPPLE

(SUPPLIED BY SPRINKLER CONTRACTOR)

PURGE BALL VALVE, SHOWN

IN CLOSED (NON-PURGE) POSITION

VENT

UNION - POSITION VENT/ORIFICE/INS-PV

APPROPRIATELY

INS-PV

INTELLIPURGE

UNION

ORIFICE

Fig. 17

Содержание INS-1500


























































Результаты поиска

Содержание INS-1500

Отзывы:

Intelligen INS-1500, Инструкция по установке, эксплуатации и обслуживанию, Страница: 15 / 57

Результаты поиска

Содержание INS-1500

Отзывы: