User guide
XSS 8000
Wireless siren
Congratulations, you have just purchased a product with Intelbras quality and security.
The XSS 8000 wireless siren was developed for status audible warning, instructions and
emergency indications from the AMT 8000 alarm center. The communication between
siren and center is made by wireless signal, providing a simpler installation and reaching a
maximum distance of up to 600 meters. Up to 16 XSS 8000 sirens can be added to each AMT
8000 center unit.
1. Care and security
» Follow all instructions in the manual/guide for product installation and handling.
» Check that the installation site is not restricted to audible signals by the sound power of
the siren.
» Perform the installation in environments not susceptible to factors such as rain, fog and
splashes of water.
» The wireless communication technology, when exposed to environments with high power
radiation, may suffer interference and have its performance impaired. Example: locations
near TV towers, AM/FM radio stations, amateur radio stations, etc.
» Do not install the siren for air conditioning or heating equipment.
» Clean only the external part of the device, using only a damp cloth (do not use chemical
solvents);
» Do not subject the device to excessive pressure or knocks/falls.
» Do not cover the device with adhesives, paper or inks.
» Do not expose directly to sunlight.
» Confirm that the installation site is stable and appropriate;
» Only perform configurations and installations by qualified personnel.
» Perform periodic tests on it to validate weather conditions, battery level and other factors so
that the site supervised by the system is always able to operate properly.
2. Technical specifications
Audible power generated
100 decibels at 1 (one) meter
Frequency of operation
RF signal from 915 to 928 MHz
Modulation
DSSS BPSK 40 kbps
Maximum transmission power
11 dBm
Transmission range
1
up to 600 m with direct line of sight open field
Power supply
Li-SoCl2 3.6 V 14 A Wired/Connector
Operating temperature
–10 to 50 °C @ 90% of humidity
Compatibility
Alarm center AMT 8000
ANATEL Homologation
Yes
Protection against violation
Tamper key
Anti-jamming
Against invasive signals
Color
White
Dimensions (W × H × D)
122 × 122 × 47 mm
Weight
256 grams
1
Intelbras wireless systems are tested to the highest standards and bring high reliability, but due to
their use/installation in various scenarios, some considerations must be taken into account:
»
Transmitters/receivers may be disturbed by radio signals, natural interference, location of
operation of the devices, climatic issues and other adversities affecting the transmission
of data regardless of the frequency or technology used, since the means of transmission is
adverse and different from place to place.
»
The receivers/transmitters of the devices have an internal processing time, and only receive
the data necessary for communication between them after this particular time for the system.
»
Wireless devices must be tested regularly to determine if sources of interference exist and
to protect against possible failures.
3. Features
» Full wireless sirens for power and communication.
» Protection against malicious signals.
» Encryption in data transmission between devices.
» Ease of installation and handling.
» Long battery life.
» High sound power.
4. Initial battery activation
When the siren is turned on for the first time, the initial battery activation process will occur,
where a charge will be applied to the battery with the siren not yet registered, which will cause
the LED to flash orange for 10 seconds, have a pause of 2 seconds and repeat the charge
application on the battery for 10 seconds again to ensure proper battery performance.
If there are 4 charge cycles, that is, LED flashing 4 times in orange within 2 seconds and the
battery level is inadequate the process is finished and the LED flashes slowly in red indicating
that the siren is almost discharged or the battery level is too low and you should contact our
accredited service network.
After the initial battery activation process, the registration process should be performed. The
reading of the charge level of the battery after registration occurs every time the trigger is
generated for at least 30 seconds and if the voltage is below 3.25 V the low battery event will
be sent (further information on events of the alarm center is described in the complete manual
of the AMT 8000 alarm center).
5. Register
To register the siren with the Alarm Center, press the synchronization key on the Center and
then press the key on the siren located on its back, as shown in the image below, removing the
product from the mounting bracket. Check if the LED on the front of the Siren will flash green,
indicating the success on the registration. If the LED flashes orange, the signal is intermittent
or weak and if the LED flashes red, there was some fault and the process must be repeated.
The addressing of the siren with the Center unit will be according to the sequence performed,
respecting the maximum limit of 16 devices of this type.
Sync key of the siren
To check if the installation location of the siren is within the range of the RF signal, press the
synchronization key on the siren, and if the LED flashes green the communication is correct, in
orange the communication is intermittent/weak and in red there is no communication with the
center. If there is no signal or weak signal, it must be relocated/changed if necessary.
To physically delete a registered siren from an alarm center, hold down the synchronization key
on the device for 20 seconds until the LED flashes red twice. When deleting sirens physically,
they must be deleted from the center memory via programming. Otherwise, a wireless device
supervision failure will be generated.
To register other sirens/accessories through keyboard commands and more information/
configurations, refer to the complete manual of the AMT 8000 center unit.
Note:
when registering the XSS 8000 siren to the alarm center using the synchronization key,
perform the practice safely, because the alarm center is energized, so as not to bring risks to
the installer and the equipment.
