manualshive.com logo in svg

Intel Stratix 10, Руководство пользователя

Поделиться
Скачать
Intel Stratix 10 Скачать руководство пользователя страница 193

Address

Name

Description

Reset

0x244

rsfec_corr_syms_cnt_0_hi RS-FEC number of 10b symbols corrected for the lane (high word:

bits 63 to 32)

0x0000 0000

0x24C

rsfec_corr_syms_cnt_1_hi

0x254

rsfec_corr_syms_cnt_2_hi

0x25C

rsfec_corr_syms_cnt_3_hi

0x260

rsfec_corr_0s_cnt_0_lo

RS-FEC number of bits corrected 0->1 for the lane (low word: bits

31 to 0)

0x0000 0000

0x268

rsfec_corr_0s_cnt_1_lo

0x270

rsfec_corr_0s_cnt_2_lo

0x278

rsfec_corr_0s_cnt_3_lo

0x264

rsfec_corr_0s_cnt_0_hi

RS-FEC number of bits corrected 0->1 for the lane (high word: bits

63 to 32)

0x0000 0000

0x26C

rsfec_corr_0s_cnt_1_hi

0x274

rsfec_corr_0s_cnt_2_hi

0x27C

rsfec_corr_0s_cnt_3_hi

0x280

rsfec_corr_1s_cnt_0_lo

RS-FEC number of bits corrected 1->0 for the lane (low word: bits

31 to 0)

0x0000 0000

0x288

rsfec_corr_1s_cnt_1_lo

0x290

rsfec_corr_1s_cnt_2_lo

0x298

rsfec_corr_1s_cnt_3_lo

0x284

rsfec_corr_1s_cnt_0_hi

RS-FEC number of bits corrected 1->0 for the lane (high word: bits

63 to 32)

0x0000 0000

0x28C

rsfec_corr_1s_cnt_1_hi

0x294

rsfec_corr_1s_cnt_2_hi

0x29C

rsfec_corr_1s_cnt_3_hi

All statistic registers are 64 bits, and you must do two 32-bit reads. Intel recommends
that you enable the 

shadow_req[3:0]

 in offset address 0x108 explained in

rsfec_debug_cfg before reading the statistics register and disable after reading it.

Related Information
rsfec_debug_cfg

 on page 198

9.5.1. rsfec_top_clk_cfg

Description

Address

Addressing Mode

RS-FEC Clock configuration register

0x4

32-bits

The reset values in this table represents register values after a reset has completed.

Bit

Name

Description

SW Access

HW Access

Protection

Reset

11:8 fec_lane_ena Rsfec Clock/Lane Enable

RW
RO
-

0xF

continued...   

9. Register Map

UG-20056 | 2019.02.04

Send Feedback

Intel

®

 Stratix

®

 10 E-Tile Transceiver PHY User Guide

193

Содержание Stratix 10





































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды