Intel Stratix 10 Скачать руководство пользователя | Manualshive

Страница: 104 / 228

background image

Block Diagram with Independent TX and RX Reset Control" and "Reset Block Diagram

with Single Reset Control" in Automatic Reset Mode show the reset IP in both

conditions.

You can use the reset controller in automatic or manual reset mode for PMA direct

modes, but you need to use the reset controller bypass when using the RS-FEC block

in fractured mode or if you want to reconfigure from RS-FEC On to RS-FEC Off or from

RS-FEC Off to RS-FEC On.

Resets signals for the Ethernet Hard IP are not included. See E-tile Hard IP for

Ethernet Intel FPGA IP User Guide for details.

Related Information

•

High Level Specification

•

Automatic Reset Mode

on page 105

•

E-tile Hard IP for Ethernet Intel FPGA IP User Guide

6.4. PMA Analog Reset

The transceiver has an internal controller that is clocked by the transceiver's reference

clock.

Table 46.

When to Perform a PMA Analog Reset

Action

Impact

During the debug phase, going from an internal

or serial loopback mode to mission mode and

back to the internal or serial loopback mode

The PMA is stuck in an unknown state; there is a high BER reported with

no CDR lock; initial adaptation does not help in recovery.

While continuous adaptation is running,

unplugging the optical link then plugging it back

in

The PMA is stuck in an unknown state; there is a high BER reported with

no CDR lock; initial adaptation does not help in recovery.

Powering up

Initial adaptation does not help bring up the device in a good state.

Correcting a loose cable connection and bring

up a link

Initial adaptation does not help bring up the device in a good state.

Disabling and re-enabling SERDES TX and RX

Initial adaptation does not help bring up the device in a good state;

some channels have a high BER until a reset is completed.

To reset the internal controller, use the transceiver’s AVMM bus to:
1. Write 0x200[7:0] = 0x00.
2. Write 0x201[7:0] = 0x00.
3. Write 0x202[7:0] = 0x00.
4. Write 0x203[7:0] = 0x81.
5. Poll 0x207[7] until it becomes 1. This indicates the reset is finished. 0x207[7] self-

clears after being read.

6. Read 0x204[0]. It should be 0 to indicate successful reset.

Resetting the internal controller causes the transceiver to lose its settings for datarate,

serialization/deserialization values, etc. You can write 0x91[0] = 1 to load the initial

settings in the programming file (when the embedded MIF streamer is not used) or go

to the last profile (when the embedded MIF streamer is used) after step 6 above .

6. Resetting Transceiver Channels

UG-20056 | 2019.02.04

Intel

®

Stratix

®

10 E-Tile Transceiver PHY User Guide

Send Feedback

104

«
...
102
103
104
105
106
...
»

Содержание Stratix 10





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Stratix 10

Бренд: Datasat Страницы: 170

Бренд: Q-See Страницы: 2

Бренд: Omega Engineering Страницы: 34

Бренд: Variscite Страницы: 18

Бренд: ZKTeco Страницы: 68

Бренд: ZALMAN Страницы: 7

Бренд: Avenview Страницы: 28

Бренд: CAME Страницы: 32

Бренд: IBM Страницы: 74

NC-MCO - TECHNICAL

Бренд: Crest Audio Страницы: 2

airPoint Nexus sB3210

Бренд: SmartBridges Страницы: 55

Бренд: Vxl Страницы: 4

Бренд: Idis Страницы: 40

Бренд: ADTRAN Страницы: 4

mvHYPERION-32R16

Бренд: Matrix Vision Страницы: 148

Бренд: Bdcom Страницы: 25

BD7682FJ-EVK-301

Бренд: Rohm Страницы: 6

Dual Window Multi-Graphic Processor MGP 462

Бренд: Extron electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды