Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 88

Страница: 88 / 162

Intel

Server System SR2612UR Service Guide

Restoring the BIOS Defaults

If you need to restore the BIOS default settings, the BIOS Default jumper will need to be
used.

1. Power down the system; do not disconnect the AC power.

2. Open the server system. For instructions on removing the system cover, see

“Removing the System Cover” on page 48

3. Locate the BIOS Default jumper block at board position J1E7.

4. Move the jumper from the normal operation position (covering pins 1 and 2) to the

Set Default position (covering pins 2 and 3).

5. Wait five seconds.

6. Return the BIOS Default jumper to the normal position (covering pins 1 and 2).

7. Close the server system.

8. Power up the system.

The BIOS defaults settings are now restored and can be reset by going into the BIOS
setup.

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды