Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 55

Страница: 55 / 162

Intel

Server System SR2612UR Service Guide

10. Using the SATA cable supplied with the drive, route the cable from each disk drive

to the CPU server board SATA connectors.

Figure 32. Connections Diagram

11. Carefully reinstall the CPU server board air duct.

12. Reinstall the top cover and tighten the captive screw.

13. Reinstall the power cord(s).

DVD Installation

The Intel

Server System SR2612UR supports an optional DVD. Complete the following

steps to install a DVD drive in the Intel® Server System SR2612UR.

1. Ensure the AC power cord(s) are disconnected from the enclosure.

2. Remove the top cover from the enclosure by loosening the captive screw with a

Phillips screwdriver on the right rear of the enclosure.

3. Slide the top cover back and lift it from the enclosure.

4. On the rear of the enclosure, locate the removable DVD cover plate.

5. Remove the four screws and cover plate using a Phillips* screwdriver shown in the

following figure.

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды