Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 40

Страница: 40 / 162

Intel

Server System SR2612UR Service Guide

SAS/SATA Midplanes

The midplane serves as the primary interface between the server board, hot-swap
backplane, and control panel. Only one midplane is offered for this system:

•

Active SAS midplane

Note: SATA connectors 6 and 7 are not used in the Intel

Server System SR2612UR.

Active Midplane

The following diagram show the location for each connector found on the active
midplane.

Figure 17. Active SAS Midplane Components

SAS Connector

Backplane Connector

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды