Intel SR2612UR - Server System - 0 MB RAM Скачать руководство пользователя страница 36

Страница: 36 / 162

Intel

Server System SR2612UR Service Guide

Figure 14. Configuration Jumpers

Front of Intel

Server System SR2612UR

Peripheral Devices

The Intel

Server System SR2612UR provides locations and hardware for installing hard

drives, CD-ROM drive, or DVD-ROM drive. The drives must be purchased separately.
The following figure shows the available options.

BIOS Recover (J1D4)

If pins 2-3 are jumpered, the system can only boot from EFI-
bootable recovery media with the recovery BIOS image. The main
system BIOS will not boot. These pins should be jumpered on 1-2
for normal system operation.

Jumper Name

Jumper Purpose

Содержание SR2612UR - Server System - 0 MB RAM



































































































































































Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды

Intel SR2612UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2612UR - Server System - 0 MB RAM

Отзывы:

Похожие инструкции для SR2612UR - Server System - 0 MB RAM

Бренды по названию

Популярные бренды