Intel SR2600UR - Server System - 0 MB RAM Скачать руководство пользователя страница 57

Страница: 57 / 234

Intel

Server System SR2600UR/SR2625UR Service Guide

Figure 22. Hot-Swap SAS/SATA Backplane Components (Rear View)

RAID Support

The server system provides an embedded SATA controller on the server board that is

accessible through the passive midplane. The SATA controller supports both 1.5 and 3.0

Gbps data transfer rates.

The BIOS Setup utility provides multiple drive configuration options on the Advanced |

ATA Controller setup page, some of which affect the ability to configure RAID. The

Onboard SATA Controller option is enabled by default. When this option is enabled, the

SATA Mode option can be set to either Legacy or Enhanced. The Legacy and Enhanced

modes affect the RAID configuration as follows:

•

Legacy supports four disk drives and does not provide RAID support.

•

Enhanced supports six disk drives and is required for RAID configurations.

When the enhanced mode is selected, you can choose to enable or disable “AHCI Mode”

or “Configure SATA as RAID”. The Intel

Embedded Server RAID Technology II is

enabled by the “Configure SATA as RAID” option. The Intel

Embedded Server RAID

Technology II feature provides RAID modes 0, 1, and 10.

AF002789

50-pin Control Panel Connector

D. Power Connector

10-pin USB Connector for Control Panel

Midplane Connectors

C. Power Connector (for tape drive or 2.5-inch

fixed drives)

Содержание SR2600UR - Server System - 0 MB RAM











































































































































































































































Результаты поиска

Содержание SR2600UR - Server System - 0 MB RAM

Отзывы:

Бренды по названию

Популярные бренды

Intel SR2600UR - Server System - 0 MB RAM, Руководство по обслуживанию

Результаты поиска

Содержание SR2600UR - Server System - 0 MB RAM

Отзывы:

Бренды по названию

Популярные бренды