manualshive.com logo in svg

Intel SR2600UR - Server System - 0 MB RAM, Руководство по обслуживанию

Поделиться
Скачать
Intel SR2600UR - Server System - 0 MB RAM Скачать руководство пользователя страница 52

32

Intel

®

 Server System SR2600UR/SR2625UR Service Guide

SAS/SATA Midplanes

The midplane serves as the primary interface between the server board, hot-swap 

backplane, and control panel. Two midplanes are offered for this system: 

•

Passive SATA/SAS midplane (data cables required) 

•

Active SAS/SATA RAID midplane (no data cables required)

Passive Midplane

The following diagram show the location for each connector found on the passive 

midplane.

Figure 17. Passive Midplane Components

Note:

SATA connectors 6 and 7 are not used in the Intel

® 

Server System SR2600UR/SR2625UR.

AF000047

E

A

J

B

C

F

G

I

H

D

A.

Midplane Power Connector

F.

Fan 4 Power Connector

B.

Fan 6 Power Connector

G. Fan 3 Power Connector

C. Fan 5 Power Connector

H. Fan 1 Power Connector

D. SATA 0-7 Connectors

I.

Fan 2 Power Connector

E.

Bridge Board Connector

J.

Backplane Connectors

Содержание SR2600UR - Server System - 0 MB RAM











































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды