Intel SR1630GP - Server System - 0 MB RAM Скачать руководство пользователя страница 130

Страница: 130 / 196

108

Intel

Server System SR1630GP / SR1630HGP Service Guide

Check the following:

•

Is the power-on light lit? If not, see

“Power Light Does Not Light” on page 106

•

Are any other front panel LEDs lit?

•

Have any of the fan motors stopped? Use the server management subsystem to

check the fan status.

•

Have your fans speeded up in response to an overheating situation?

•

Have your fans speeded up in response to a fan that has failed?

•

Are the fan power connectors properly connected to the server board?

•

Is the cable from the front panel board connected to the both the front panel board

and to the server board?

•

Are the power supply cables properly connected to the server board?

• Are there any shorted wires caused by pinched-cables or have power connector

plugs been forced into power connector sockets the wrong way?

Drive Activity Light Does Not Light

Check the following:

•

Are the drive's power and signal cables properly installed?

•

Are all relevant switches and jumpers on the drive set correctly?

•

Is the drive properly configured?

• Is the drive activity light always on? If so, the signal cable may be plugged in

incorrectly.

CD-ROM Drive or DVD-ROM Drive Activity Light Does Not
Light

Check the following:

•

Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed?

•

Are all relevant switches and jumpers on the drive set correctly?

• Is the drive properly configured?

Cannot Connect to a Server

•

Make sure the network cable is securely attached to the correct connector at the

system back panel.

•

Try a different network cable.

•

Make sure you are using the correct and the current drivers. See

“Server System

References” on page x

for a link to the current drivers.

Содержание SR1630GP - Server System - 0 MB RAM





































































































































































































Результаты поиска

Содержание SR1630GP - Server System - 0 MB RAM

Отзывы:

Intel SR1630GP - Server System - 0 MB RAM, Руководство по обслуживанию, Страница: 130 / 196

Результаты поиска

Содержание SR1630GP - Server System - 0 MB RAM

Отзывы: