Intel R2600SR Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 85

background image

Intel® Server System R2600SR Setup and Service Guide

36

3.7

Replacing the Drive Carrier

Each compute node within the system is pre-populated with an SSD installed in a drive carrier. The single
SSD in its pre-populated drive bay is the only drive supported in this system.

3.7.1

Extracting the Drive Carrier

Figure 29. Extracting the drive carrier

To extract (remove) a drive carrier, complete the following steps:

1.

Pressing the button on the carrier face plate to release the locking lever.

2.

Using the lever, pull the carrier straight out and away from the drive bay.

3.7.2

Installing the Drive Carrier

Figure 30. Installing a drive carrier

To install a drive carrier, complete the following steps:

1.

Align the drive carrier with the open drive bay.

2.

With the locking lever in the open position, insert the drive carrier into the drive bay and push
forward until the drive makes contact with the backplane.

3.

Close the drive carrier locking lever until it locks into place to complete the installation.

«
...
40
41
42
43
44
...
»

Содержание R2600SR Series






















































































Отзывы:

Нет отзывов

Похожие инструкции для R2600SR Series

Бренд: Xerox Страницы: 12

Бренд: Aastra Страницы: 502

Бренд: Korenix Страницы: 2

Virtual Services Platform 7000 Series

Бренд: Avaya Страницы: 103

Бренд: Edimax Страницы: 93

Бренд: Novell Страницы: 152

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Бренд: LaCie Страницы: 67

eserver iSeries 270

Бренд: IBM Страницы: 40

Бренд: Kontron Страницы: 90

HPE ProLiant DL580 Gen10

Бренд: Hewlett Packard Enterprise Страницы: 197

AAEON ARES-WHI0

Бренд: Asus Страницы: 76

Бренд: Asus Страницы: 16

Бренд: Asus Страницы: 42

RS720A-E9-RS24-E

Бренд: Asus Страницы: 162

Бренд: Asus Страницы: 164

TS700-E9 Series

Бренд: Asus Страницы: 178

Бренд: Asus Страницы: 224

Бренд: Asus Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды