manualshive.com logo in svg

Intel Quark SE C1000, Руководство по платформе

Поделиться
Скачать
Intel Quark SE C1000 Скачать руководство пользователя страница 34

SPI 

Intel® Quark™ SE Microcontroller C1000 
Platform Design Guide 

June 2017 

34  

Document Number: 334715-004EN 

7.0

 

SPI 

The Serial I/O implements two SPI controllers that support master mode and one 
SPI controller that supports slave mode. Refer to the Intel® Quark™ SE 
Microcontroller C1000 Datasheet for additional SPI compatibility requirements and 
features. Support for SPI Flash devices is a key platform requirement and is needed 
for all SoC designs. 

Table 14.  SPI Signals 

Signal Name 

Direction/ Type 

Description 

SPI_M_x_SCK 

Output 

SPI Serial Clock 

SPI_M_x_CS_B[3:0] 

Output 

SPI Chip Select 

SPI_M_x_MOSI 

Output 

SPI Master Output Slave Input 

SPI_M_x_MISO 

Input 

SPI Master Input Slave Output 

The Intel® Quark™ SE microcontroller C1000 includes the following: 

Two SPI master interfaces with support for SPI clock frequencies up to 16 MHz

One SPI slave interface with support for SPI clock frequencies up to 3.2 MHz

Support for 4-bit up to 32-bit frame size

Up to four Slave Select pins per master interface

FIFO mode support (16B TX and RX FIFOs)

Support for HW DMA with configurable FIFO thresholds

7.1

 

Signal Descriptions 

Figure 15.  SPI Point-to-Point Single Flash Topology 

TL0

TL1

TL2

FLASH 

Device

Single Load

MOSI/MISO/SPI_IO/CLK/CS

ATP SoC

Rs

Table 15.  SPI Single Flash Platform Routing Guidelines 

SPI Single Flash 

MOSI/MISO/SPI_IO/CLK/CS 

SoC Breakout 

Main Routing 

Device Breakout 

Transmission Line Segment 

TL0 

TL1 

TL2 

Содержание Quark SE C1000


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды