Intel PXA27x Series Скачать руководство пользователя страница 75

Страница: 75 / 88

Intel

PXA27x Processor Developer’s Kit - User’s Guide

3.3.1.9

Synchronous Static Memory Configuration Register (SXCNFG)

Before

setting up SXCNFG, configure the Intel

PXA270 Processor flash-memory devices for

synchronous operation. To do this, refer to the

Intel

Synchronous StrataFlash

Memory Data

Sheet

for the K18-family devices. In the Flash Configuration register for each device, set the first-

access latency count (CR[13:11]) to 0b011.

SXCNFG Recommended Settings:

3.3.1.10

Expansion Memory Timing Configuration Registers

The following table shows the settings for

all six

of these configuration registers.

Note:

The values in the following table presume a 250-ns card cycle time.

MCMEM0, MCMEM1, MCATT0, MCATT1, MCIO0, and MCIO1
Recommended Settings:

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

Stand-alone Intel

PXA270 Processor

and

Intel

PXA270 Processor with main board

000 0000

001

000 0000

001

†

These values are based upon the main board switch SW2 (SWAP_FLASH) being set to

DOT

(nCS0 = Intel

PXA270 Processor

flash). If SWAP_FLASH is set to

NO-DOT

(nCS0 = main board flash), then the values of these bits must be swapped.

To determine the state of SWAP_FLASH, software must use the procedure described in

Section 3.2.1

to access the System

Configuration Register (see

Table 16

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

Stand-alone Intel

PXA270 Processor

0000 0000 0000

XX XXXX

X XXXX

XXX XXXX

Processor card with main board

0000 0000 0000

00 0111

0 0111

001 0001

Содержание PXA27x Series

























































































Результаты поиска

Содержание PXA27x Series

Отзывы:

Похожие инструкции для PXA27x Series

Бренды по названию

Популярные бренды

Intel PXA27x Series, Руководство пользователя

Результаты поиска

Содержание PXA27x Series

Отзывы:

Похожие инструкции для PXA27x Series

Бренды по названию

Популярные бренды