manualshive.com logo in svg

Intel Omni-Path Director Class Switch Series, Руководство по установке

Поделиться
Скачать
Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 78

Figure 62.

Activating the FM Enable Switch LED

The FM Enable Switch is used as follows:

NOTE

Actions take place approximately 1 second after releasing the button.

•

Pressing the button for 4 seconds does a "Restore Factory Defaults" and reboots

the ASIC.

•

Pressing the button for 2 seconds (and then releasing) puts the "FM control button

persistent state" in configuration mode.
— The FM enabled LED will blink "n" times, where "n" is the current state value

plus 1.

— Pressing (and releasing) the button once for less than 2 seconds advances the

FM control persistent state by 1 (round-robin), and then it returns to step 1

(i.e., blinking the FM enabled LED).

— Pressing the button for 2 seconds leaves the configuration state, and saves the

FM control button state persistently, restoring the FM enabled LED to the

proper value.

Intel

®

 Omni-Path Fabric—Installation

Intel

®

 Omni-Path Fabric Switches Hardware

Installation Guide

June 2019

78

Doc. No.: H76456, Rev.: 10.0

Содержание Omni-Path Director Class Switch Series




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды