manualshive.com logo in svg

Intel Omni-Path Director Class Switch Series, Руководство по установке

Поделиться
Скачать
Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 76

Edge Switch LEDs

Figure 60.

Edge Switch LEDs

RJ45 LEDs

The RJ45 connectors have two LEDs, Link and Speed. The Speed LED is 

Green

 when

a 100 Mbps link is connected. The Link LED is 

Amber

 when an Ethernet link has been

established, and blinking when the link is active.

Chassis Status LEDs

Status (STAT)

The status LED indicates one of the following conditions:
•

Steady 

Green

: the module is operating normally.

•

Blinking 

Green

: LED test state.

•

Off: module is in the removable state.

Attention (ATTN)

The Attention LED indicates one of the following conditions:
•

Off: the system functioning normally.

•

Steady 

Amber

: the system requires some attention, which could indicate one of

the following conditions:
— The switch temperature is at a warning level on the module.
— The switch silicon temperature is at a warning level (approximately 90 degrees

C).

— DC voltages on the board are slightly out of tolerance (12V Bulk, 5V, 3.3V and

1.8V are all monitored).

— The module can no longer function properly. The system will take the

appropriate actions to ensure that no damage is done to its components.

•

Blinking 

Amber

 (once every four seconds): LED test state.

2.8.1  

2.8.1.1  

2.8.1.2  

Intel

®

 Omni-Path Fabric—Installation

Intel

®

 Omni-Path Fabric Switches Hardware

Installation Guide

June 2019

76

Doc. No.: H76456, Rev.: 10.0

Содержание Omni-Path Director Class Switch Series




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды