manualshive.com logo in svg

Intel Omni-Path Director Class Switch Series, Руководство по установке

Поделиться
Скачать
Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 33

2. Mark the upper (if applicable) and lower mounting positions on the vertical rails on

the front of the rack.

3. Mark the upper (if applicable) and lower mounting positions on the vertical rails on

the back of the rack.

Intel

®

 Omni-Path Fabric Edge Switch Installation

This section describes the rack mounting instructions for the 24- and 48-port Intel

®

Omni-Path Fabric Edge Switches in a four-post standard-depth rack. The installation of

either switch is very similar; the majority of steps apply to both switches. Where

applicable, any specifics for either switch are called out.

In a standard-depth rack, the distance between the front and back mounting posts is

~28" (700 mm). Mounting rails for the switch are adjustable to accommodate racks

with 26"–32" between mounting posts.

Mounting Hardware Kit Contents

The Mounting Kit contains:
•

ESD wrist strap

•

One pair of mounting rails adjustable for 26"–32" installation range

•

M6 hex head screws

•

Front 1U perforated cover

Rack Mounting

Figure 5.

Intel

®

 Omni-Path Edge Switch Rail

1. Insert the rail installation pin in to the rack hole as shown in the following figure.

This holds the rail in place so the user can install the fan side screws.

2.3  

2.3.1  

2.3.2  

Installation—Intel

®

 Omni-Path Fabric

Intel

®

 Omni-Path Fabric Switches Hardware

June 2019

Installation Guide

Doc. No.: H76456, Rev.: 10.0

33

Содержание Omni-Path Director Class Switch Series




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды