manualshive.com logo in svg

Intel Omni-Path Director Class Switch Series, Руководство по установке

Поделиться
Скачать
Intel Omni-Path Director Class Switch Series Скачать руководство пользователя страница 28

2.0 

Installation

This section describes how to install and configure for first-time use:
•

The Intel

®

 Omni-Path Fabric Series switches in a network environment.

Planning the Installation

The Intel

®

 Omni-Path switches are designed for installation in standard 19-inch

equipment racks.

Racks should conform to conventional standards. Use the American National

Standards Institute (ANSI)/Electronic Industries Association (EIA) standard ANSI/

EIA-310-D-92 and International Electrotechnical Commission (IEC) 297

Racks should meet the following mechanical recommendations:
•

Four-post, 19" rack to facilitate easy maintenance

•

Universal mounting rail hole pattern identified in IEC Standard 297

•

Mounting holes flush with the rails to accommodate the chassis

NOTE

Operation is subject to the following conditions:

NOTE

Use a rack grounding kit and a ground conductor that is carried back to earth or to

another suitable building ground. Ground the equipment rack to earth ground.

NOTE

Provide enough room to work on the equipment. Clear the work site of any

unnecessary materials. Make sure the equipment will have enough clearance for front

and rear access.

Cable Requirements

Cable Distances

When planning the location of the switches, consider the distance limitations for

signaling, EMI, and connector compatibility. It is recommended that the user does not

exceed specified transmission rate and distance limits.

NOTE

When connecting the outer ports of two (2) 48-port Edge switches (highlighted green

in Figure 1 below), make certain to use active optical cables (AOC) for distances

greater than 2 meters.

2.1  

2.1.1  

2.1.1.1  

Intel

®

 Omni-Path Fabric—Installation

Intel

®

 Omni-Path Fabric Switches Hardware

Installation Guide

June 2019

28

Doc. No.: H76456, Rev.: 10.0

Содержание Omni-Path Director Class Switch Series




























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды