Intel IXP45X Скачать руководство пользователя страница 624

Страница: 624 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors—Memory Controller

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Developer’s Manual

August 2006

624

Order Number: 306262-004US

Referring to

Figure 121

, the syndrome bits are created by XORing the data bits as

indicated by the appropriate row of the G-Matrix in

Figure 119

with the corresponding

ECC bit. For example, the MCU derives syndrome bit 0 by XORing data bits 0, 4, 8, 12,

16, 20, 25, 29..31, 40..43, 48..56, 58, 59, 62, and ECC bit 0 (physically read on

DDRI_CB[7:0]). The MCU performs eight such XOR operations (one per syndrome bit).

If decoding the syndrome indicates multi-bit error (see

Table 213

), the transaction

results in a target-error for Internal Bus transactions, or a multi-bit error in the BIU for

Core transactions. If an internal bus master detects a target-abort, the master asserts

an interrupt to the core. Write cycles are posted to the memory transaction queues,

and already completed to the initiating master. For write cycles with a multi-bit error

and with ECC Error reporting enabled, the MCU reports the interrupt in the MCISR and

interrupts the core.

If the syndrome indicates a single-bit error and single-bit error correction is enabled,

the H-Matrix is used to determine the bit in error (see

Figure 122

). For example, if the

syndrome was 1100 0001, the error is with bit 0 of DDRI_DQ[31:0]. The MCU inverts

bit 0 before driving the data on DATA[63:0].

If error reporting is enabled in the ECCR and the MCU detects a single-bit or multi-bit

error, the MCU stores the address in ECARx and the syndrome in ELOGx. Then, the

MCU signals an interrupt to the core. Software decides how to proceed through an

interrupt handler. By registering the address in ECARx, software can identify the faulty

DIMM.

For details about the MCU error conditions and how the MMR registers are affected,

refer to

“Interrupts/Error Conditions” on page 627

Note:

In 32-bit wide memory, the DDRI SDRAM Control Block will still generate 8-bit wide

ECC by zero-extending the data to 64-bits. A partial write is a write of less than

4 Bytes.

11.2.3.4

Scrubbing

Fixing the data error in memory is called scrubbing. The IXP45X/IXP46X network

processors rely on Intel XScale processor software to perform the scrubbing. When the

MCU detects an error during a read, the MCU logs the address where the error occurred

and interrupts the Intel XScale processor. The Intel XScale processor decides how to fix

the error through an interrupt handler. Software could decide to perform the scrubbing

on:

• the data location that failed
• the entire row of the data that failed
• the entire memory

For single-bit errors reported on a write transaction scrubbing is not required, as the

MCU will have scrubbed the data during the RMW operation. For single-bit errors, the

error is fixed by reading the location that failed and writing back the data after the ECC

hardware fixed it. The scrubbing routine should read either DWORD of the 64-bit

memory space (QWORD aligned location) using an

instruction and write the data

back with an

instruction. Software should isolate activity on the memory location to

guarantee atomicity.

Note:

If the scrubbing routine reads the failed location in order to fix the single-bit error, a

second error will be reported. Therefore, software should disable single-bit ECC

reporting during the scrubbing routine. Also, the scrubbing routine should be aware

that partial writes will automatically scrub the QWORD aligned location if it contains a

single-bit ECC error.

Multi-bit errors cannot be fixed by the H-Matrix.

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды