Intel IXP45X Скачать руководство пользователя страница 549

Страница: 549 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

August 2006

Develepor’s Manual

Order Number: 306262-004US

549

PCI Controller—Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

Note that DMA completions can generate an interrupt on the DMA interrupt outputs or

on the general-purpose interrupt PCC_INT. Separate DMA interrupt enables are

provided for each interrupt output signal but there remains just one interrupt source

for each DMA channel in the DMA Control register.

10.4

PCI RCOMP Circuitry

The PCI RCOMP circuitry dynamically compensates for variations in operating

conditions due to process, temperature and voltage. These variations are measured

through a resistive mechanism in a special I/O Pad and evaluated in the associated

compensation circuitry. Adjustments are made to the drive strength of the buffers for

the PCI interface ensuring error free operation over the entire range of operating

conditions.

The RCOMP circuitry requires an external reference resistor that models the load the

PCI pads will see in the board environment. For specific RCOMP pin requirements, see

the Intel

IXP45X and Intel

IXP46X Product Line of Network Processors Datasheet.

The circuitry adjusts the PCI pads' current sourcing strength by comparing the voltage

of the output buffer driven through the external reference resistor with an internally

generated 60% threshold voltage. The circuitry adjusts the PCI pads' current sinking

strength by comparing the output buffer voltage with an internally generated 40%

threshold voltage. Once drive strengths are determined for the 60% and 40%

thresholds a multiplier is applied to the drive strengths to provide for a margin above

and below the 60% and 40% thresholds, respectively.

10.5

Register Descriptions

The following sections describe the internal PCI Configuration registers. Registers or

fields defined as reserved return 0s when read and are not affected by writes. The

access key is as follows:

10.5.1

PCI Configuration Registers

These registers comprise the configuration registers as defined in the PCI 2.2

specification with the exception of the pci_rtotto register which is device specific. They

are accessible from the PCI bus using configuration read and write transactions and

from the Intel XScale processor by accessing the PCI Controller CSR-based PCI

Configuration register port.

Table 200

lists the registers.

Table 199.

Register Legend

Attribute

Legend

Attribute

Legend

Reserved

Read Clear

Preserved

Read Only

Read/Set

Write Only

Read/Write

Not Accessible

RW1C

Normal Read

Write ‘1’ to clear

RW1S

Normal Read

Write ‘1’ to set

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды