Intel IXP45X Скачать руководство пользователя страница 501

Страница: 501 / 958

Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

August 2006

Develepor’s Manual

Order Number: 306262-004US

501

PCI Controller—Intel

IXP45X and Intel

IXP46X Product Line of Network Processors

10.2.2

PCI Controller Configured as Host

The IXP45X/IXP46X network processors can be configured as a host function on the

PCI bus. Configuring the IXP45X/IXP46X network processors as a host does not require

the internal PCI arbiter function in the PCI Controller to be enabled.

The first step to using the PCI interface in any mode of operation is to determine the

mode of operation and then configure the interface. The PCI bus mode of operation can

be obtained by reading bit 0 of the PCI Controller Control and Status Register

(PCI_CSR). If bit 0 of the PCI Controller Control and Status Register (PCI_CSR) is set to

logic 0, the IXP45X/IXP46X network processors are required to function as an Option

on the PCI bus. If bit 0 of the PCI Controller Control and Status Register (PCI_CSR) is

set to logic 1, the IXP45X/IXP46X network processors are required to function as the

Host on the PCI bus.

Bit 0 of the PCI Controller Control and Status Register (PCI_CSR) will be set by the

logic level contained on Expansion Bus Address Bus bit 1 at the de-assertion of the

reset signal supplied to the IXP45X/IXP46X network processors. The internal arbiter

will be enabled/disabled based on the logic level contained on Expansion Bus Address

Bus bit 2 at the de-assertion of the reset signal supplied to the IXP45X/IXP46X network

processors. The PCI Controller Control and Status Register (PCI_CSR) bit 1 captures

the logic level contained on Expansion Bus Address Bus bit 2 at the de-assertion of

reset.

If bit 1 of the PCI Controller Control and Status Register (PCI_CSR) is set to logic 1, the

internal arbiter is enabled on the IXP45X/IXP46X network processors. If bit 1 of the PCI

Controller Control and Status Register (PCI_CSR) is set to logic 0, the internal arbiter is

disabled on the IXP45X/IXP46X network processors.

Once the PCI controller has determined that the mode of operation is to be host, the

IXP45X/IXP46X network processors are required to configure the rest of the PCI bus.

However, before the IXP45X/IXP46X network processors can configure the rest of the

PCI bus, the PCI Controller must be configured.

The Configuration and Status Registers must be initialized and the PCI Controller

Configuration and Status Registers must be initialized. (For more detail on initializing

the Configuration and Status Registers, see

“Initializing PCI Controller Configuration

and Status Registers for Data Transactions” on page 505

. For more detail on initializing

the PCI Controller Configuration and Status Registers, see

“Initializing the PCI

Controller Configuration Registers” on page 509

After the local Configuration and Status Register and PCI Controller Configuration and

Status Registers have been initialized, the remainder of the PCI bus is ready to be

configured by the hosting network processor. The IXP45X/IXP46X network processors

will now begin to initiate configuration cycles to all of the potential devices on the PCI

bus.

The order and nature in which the devices are learned is up to the individual

application. However, one bit must be configured prior to initiating PCI Configuration

Cycles with the IXP45X/IXP46X network processors. Bit 2 of the PCI Control Register/

Status (PCI_SRCR) Register must be set to logic 1 using the methods described in

“Initializing the PCI Controller Configuration Registers” on page 509

. The setting of bit

2 to logic 1 enables PCI bus-mastering capability.

Two types of PCI Configuration Cycles can be generated using the IXP45X/IXP46X

network processors: Type 0 and Type 1 Configuration Cycles. Type 0 Configuration

Cycles are use to communicate to a PCI device which is contained on the same local

segment that the generator of the Configuration Cycles. Type 1 Configuration Cycles

are use to communicate to a PCI device which is contained on another segment of the

PCI bus other than the PCI bus segment that is generating the Configuration Cycles,

i.e., a segment on the other side of a PCI bridge.

Содержание IXP45X































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды

Intel IXP45X, Руководство разработчика

Результаты поиска

Содержание IXP45X

Отзывы:

Бренды по названию

Популярные бренды