Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 13

Страница: 13 / 148

Introduction

Thermal and Mechanical Design Guidelines

1.2

References

Material and concepts available in the following documents may be beneficial when

reading this document.

Document Location

Intel

Core™2 Extreme Processor X6800 and Intel

Core™2 Duo

Desktop Processor E6000 and E4000 Series Datasheet

http://intel.com
/design/processor/datashts/3132
78.htm

Intel

Pentium

Dual-Core Desktop Processor E2000 Series

Datasheet

www.intel.com//design/processor
/datashts/316981.htm

Intel

Celeron

Dual-Core Processor E1000 Series Datasheet

http://www.intel.com/design/proc
essor/datashts/318924.htm

LGA775 Socket Mechanical Design Guide

http://intel.com/design/
Pentium4/guides/ 302666.htm

uATX SFF Design Guidance

http://www.formfactors.org/

Fan Specification for 4-wire PWM Controlled Fans

http://www.formfactors.org/

ATX Thermal Design Suggestions

http://www.formfactors.org/

microATX Thermal Design Suggestions

http://www.formfactors.org/

Balanced Technology Extended (BTX) System Design Guide

http://www.formfactors.org/

Thermally Advantaged Chassis version 1.1

http://www.intel.com/go/chassis/

1.3

Definition of Terms

Term Description

The measured ambient temperature locally surrounding the processor. The ambient
temperature should be measured just upstream of a passive heatsink or at the fan inlet
for an active heatsink.

The case temperature of the processor, measured at the geometric center of the topside
of the IHS.

The ambient air temperature external to a system chassis. This temperature is usually
measured at the chassis air inlets.

Heatsink temperature measured on the underside of the heatsink base, at a location
corresponding to

C-MAX

The maximum case temperature as specified in a component specification.

Case-to-ambient thermal characterization parameter (psi). A measure of thermal
solution performance using total package power. Defined as (T

– T

) / Total Package

Power.

Note: Heat source must be specified for

measurements.

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды