manualshive.com logo in svg

Intel 81341, Руководство разработчика

Developer'S Manual для Intel 81341 - бесплатное руководство, которое поможет вам разрабатывать на высоком уровне. Скачайте этот мануал на manualshive.com и получите всю необходимую информацию для работы с продуктом Intel 81341. Начните использовать его прямо сейчас!

Поделиться
Скачать
background image

Intel

®

 81341 and 81342 I/O Processors

December 2007

Developer’s Manual

Order Number: 315037-002US

239

Address Translation Unit (PCI Express)—Intel

®

 81341 and 81342

3.3

ATU Address Translation

The ATU allows PCI Express requesters to initiate transactions to the 81341 and 81342 

internal bus and allows the Intel XScale

®

 processor to initiate transactions in the PCI 

Express domain. 
The ATU implements an address windowing scheme to determine which addresses to 

claim and translate to the destination bus.

• The address windowing mechanism for inbound translation is described in 

Section 

3.3.1.1, “Inbound Address Translation” on page 242

.

• The address windowing mechanism for outbound translation is described in 

Section 

3.3.2, “Outbound Transactions” on page 249

 and 

Section 3.3.3, “Outbound Write 

Transaction” on page 255

.

The ATU has the ability to accept up to eight inbound PCI Express Non Posted Read 

(memory read, configuration read, and I/O read) transactions, one inbound Non Posted 

Write (configuration write and I/O write) transaction, and16 inbound PCI Express 

Posted (memory write and message) transactions simultaneously.
As a PCI Express end point, the ATU must advertise infinite credits for Completion 

Headers and Completion Data. As a requester the ATU never requests more read data 

than it has room for in its Inbound Completion queues (ICPLHQ and ICPLDQ).
Also, the ATU has the ability to accept up to eight outbound Non Posted (internal bus 

read, configuration, and I/O) transactions and four outbound Posted (internal bus write 

and message) transactions simultaneously.
Of the 8 outbound Non Posted transactions, 4 is actively requesting data while the 

other 4 remains pending until one of the earlier active transactions is completed. Each 

active outbound read request may be fragmented into sub-requests based on the 

MAX_READ_REQUEST_SIZE parameter programmed in the 

“PCI Express Device Control 

Register - PE_DCTL” on page 348

. The fragmentation may result in as many as 8 sub-

requests per active read transaction. The ATU tracks a maximum of 32 outstanding non 

posted transactions at once. Completions for these sub-requests can return out of 

order on the PCI Express interface but they are returned in order on the internal bus.
Outbound memory writes and completions may be fragmented into smaller 

transactions based on the setting of the MAX_PAYLOAD_SIZE in the 

“PCI Express 

Device Control Register - PE_DCTL” on page 348

.

Outbound completions obeys the minimum fragmentation limit of 128Bytes.
Refer to 

Figure 24

 and 

Section 3.8

 for details of the ATU queue architecture.

As a master on the internal bus, the ATU never requests more read data than it has 

room for in the Outbound Completion queues (OCPLHQ and OCPLDQ). 
Inbound memory writes are fragmented on 1KB address aligned boundaries before 

issuing on the internal bus. Since the maximum payload size supported by the PCI 

Express interface is 512 Bytes each transactions are fragmented into a maximum of 

two internal bus transactions. Additionally, write combining does not occur.
Inbound completions are attempted on the internal bus with the same payload size as 

was received from PCI Express. In most instances the PCI Express completion size is 

64B or 128B. The PCI express completions may be combined into larger completion 

transactions on the internal bus.
Inbound memory read requests are fragmented into 1KB aligned sub-requests. 

Completions for these sub-requests can be received out of order on the internal bus 

and is returned in order on the PCI Express interface.

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Rabbit 2000 Designers Handbook preview
2000
Бренд: Rabbit Страницы: 45
Rabbit 2000 Instruction & Reference Manual preview
2000
Бренд: Rabbit Страницы: 174
Rabbit 2000 Getting Started preview
2000
Бренд: Rabbit Страницы: 43
Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Бренд: Paradyne Страницы: 2
Dentsply Sirona inLab Speedcure 9494800 Instruction Manual preview
inLab Speedcure 9494800
Бренд: Dentsply Sirona Страницы: 91
Black Box JPM083A Manual preview
JPM083A
Бренд: Black Box Страницы: 9
VCS VideoJet 100 Manual preview
VideoJet 100
Бренд: VCS Страницы: 118
IDT Digital Encoder Plus User Manual preview
Digital Encoder Plus
Бренд: IDT Страницы: 98
NKE BOX Wi-Fi User Manual And Installation Manual preview
BOX Wi-Fi
Бренд: NKE Страницы: 15
Caton NVE 9100 User Manual preview
NVE 9100
Бренд: Caton Страницы: 18
NXP Semiconductors UM10301 PCA8565 User Manual preview
UM10301 PCA8565
Бренд: NXP Semiconductors Страницы: 54
B&B Electronics 4 Channel Input Buffer Board SDAIBB Product Manual preview
4 Channel Input Buffer Board SDAIBB
Бренд: B&B Electronics Страницы: 22
mikroElektronika Pressure click Quick Start Manual preview
Pressure click
Бренд: mikroElektronika Страницы: 2
Loxit 6026 Lapbank 16 mini Cable Installation preview
6026 Lapbank 16 mini
Бренд: Loxit Страницы: 2
NXP Semiconductors i.MX 8M Mini LPDDR4 EVK User Manual preview
i.MX 8M Mini LPDDR4 EVK
Бренд: NXP Semiconductors Страницы: 20
Radio Shack 26-3801 Service Manual preview
26-3801
Бренд: Radio Shack Страницы: 154
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Бренд: Kontron Страницы: 20
Alphacool HDX Pro Air Manual preview
HDX Pro Air
Бренд: Alphacool Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды