Intel 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 105

background image

Intel® Thermal/Mechanical Reference Design Information

R

44

Thermal/Mechanical Design Guide

5.2.2 Power

Cycling

Thermal performance degradation due to TIM degradation is evaluated using power cycling
testing. The test is defined by 7,500 cycles for the case temperature from room temperature
(~23 ºC) to the maximum case temperature defined by the thermal profile at TDP.

5.2.3

Recommended BIOS/Processor/Memory Test Procedures

This test is to ensure proper operation of the product before and after environmental stresses, with
the thermal mechanical enabling components assembled. The test shall be conducted on a fully
operational motherboard that has not been exposed to any testing prior to the test being
considered.

Testing setup should include the following components, properly assembled and/or connected:

•

Appropriate system motherboard

•

Processor

•

All enabling components, including socket and thermal solution parts

•

Power supply

•

Disk drive

•

Video card

•

DIMM

•

Keyboard

•

Monitor

The pass criterion is that the system under test shall successfully complete the checking of BIOS,
basic processor functions and memory, without any errors.

5.3

Material and Recycling Requirements

Material shall be resistant to fungal growth. Examples of non-resistant materials include cellulose
materials, animal and vegetable based adhesives, grease, oils, and many hydrocarbons. Synthetic
materials such as PVC formulations, certain polyurethane compositions (e.g., polyester and some
polyethers), plastics that contain organic fillers of laminating materials, paints, and varnishes also
are susceptible to fungal growth. If materials are not fungal growth resistant, then MIL-STD-
810E, Method 508.4 must be performed to determine material performance.

Material used shall not have deformation or degradation in a temperature life test.

Any plastic component exceeding 25 grams must be recyclable per the European Blue Angel
recycling standards.

«
...
42
43
44
45
46
...
»

Содержание 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU










































































































Отзывы:

Нет отзывов

Похожие инструкции для 640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Бренд: D-Link Страницы: 15

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: Keithley Страницы: 59

Бренд: Lab.gruppen Страницы: 35

Бренд: LaCie Страницы: 4

Бренд: LaCie Страницы: 4

Бренд: Paradyne Страницы: 11

Бренд: Paradyne Страницы: 19

COMSPHERE 3550 Series

Бренд: Paradyne Страницы: 153

Jetstream CPX-1000

Бренд: Paradyne Страницы: 141

Бренд: Teagle Страницы: 40

Бренд: Cypress Semiconductor Страницы: 9

Бренд: peplink Страницы: 2

SABVISION NVR32

Бренд: SAB Страницы: 29

Open Standard Module RPX30 EVA-MI V1

Бренд: iesy Страницы: 9

Airborne M2M ABDN-er-DP55 Series

Бренд: B+B SmartWorx Страницы: 120

Бренд: DigiTech Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды