Intel 6300ESB ICH Скачать руководство пользователя страница 174 | Manualshive

Страница: 174 / 320

background image

174

Design Guide

Intel

®

855GME Chipset and Intel

®

82801DB ICH4 Embedded Platform Design Guide

AGP Port Design Guidelines

7.1.2

AGP Interface Signal Groups

The signals on the AGP interface are broken into three groups: 1X timing domain signals, 2X/4X
timing domain signals, and miscellaneous signals. Each group has different routing requirements.

In addition, within the 2X/4X timing domain signals, there are three sets of signals. All signals in
the 2X/4X timing domain must meet minimum and maximum trace length requirements, as well as
trace width and spacing requirements. Because of the multiplexed AGP/DVO interface, there are
trace length matching requirements within each set of 2X/4X signals, as well as between sets of
2X/4X signals. The signal groups are listed in following table.

The routing guidelines for each group of signals (1X timing domain signals, 2X/4X timing domain
signals, and miscellaneous signals) will be addressed separately.

Table 57. AGP 2.0 Signal Groups

1x Signals

2x Signals

4x Signals

CLK (3.3 V)

GRBF#

GWBF#

GST_[2:0]

GPIPE#

GREQ#

GGNT#

GPAR

GFRAME#

GIRDY#

GTRDY#

GSTOP#

GDEVSEL#

GAD_[31:0]

GC/BE_[3:0]#

GADSTB_[1:0]

2X signals include all 1X signals and:

GADSTB_[1:0]

GSBSTB

GAD_[31:0] signals and associated
GC/BE_[3:0]# signals are running at 2X
mode.

4X signals include all 1X signals and:

GADSTB_[1:0]

GADSTB_[1:0]#

GSBSTB

GSBSTB#

GAD_[31:0] signals and associated
GC/BE_[3:0]# signals are running at 4X
mode.

Table 58. AGP 2.0 Data/Strobe Associations

Data

Associated Strobe in 1X

Associated

Strobes in 2X

Associated

Strobes in 4X

AD[15:0] and C/BE[1:0]#

Strobes are not used in 1X mode. All
data is sampled on rising clock edges.

AD_STB0

AD_STB0,

AD_STB0#

AD[31:16] and C/BE[3:2]#

Strobes are not used in 1X mode. All
data is sampled on rising clock edges.

AD_STB1

AD_STB1,

AD_STB1#

SBA[7:0]

Strobes are not used in 1X mode. All
data is sampled on rising clock edges.

SB_STB

SB_STB,

SB_STB#

«
...
172
173
174
175
176
...
»

Содержание 6300ESB ICH

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6300ESB ICH

Бренд: Cypress Semiconductor Страницы: 9

Protege PRT-PX16-PCB

Бренд: ICT Страницы: 34

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

Thin Client US310e

Бренд: NEC Страницы: 6

Бренд: ZoneVu Страницы: 15

Бренд: FUNcube Страницы: 23

POD-51EH-C541U-12

Бренд: IceTech Страницы: 8

Бренд: Intel Страницы: 154

Бренд: Renesas Страницы: 4

Бренд: Intel Страницы: 44

Sporlan Division SCS-PB Series

Бренд: Parker Страницы: 10

Бренд: ZALMAN Страницы: 32

Бренд: SilverStone Страницы: 12

Бренд: TERSUS Страницы: 7

Бренд: Adaptec Страницы: 3

DP1.2-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: JETWAY Страницы: 15

Бренд: MTI Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды