Intel 10 Gigabit AT Ethernet Server Adapter Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 165

Intel 10 Gigabit AT Ethernet Server Adapter Скачать руководство пользователя страница 87

Flags

A set of miscellaneous data either read from the adapter EEPROM or calculated by the
Boot Agent initialization code. This information varies from one adapter to the next and is
only intended for use by Intel customer support.

iSCSI Boot Configuration

iSCSI Initiator Setup

Configuring Intel

®

Ethernet iSCSI Boot on a Microsoft* Windows* Client Initiator

Requirements

1. Make sure the iSCSI initiator system starts the iSCSI Boot firmware. The firmware should be con-

figured properly, be able to connect to iSCSI target, and detect the boot disk.

2. You will need Microsoft* iSCSI Software Initiator with integrated software boot support. This boot ver-

sion of the initiator is available

.

3. To enable crash dump support, follow the steps in

Crash Dump Support

Configuring Intel

®

Ethernet iSCSI Boot on a Linux* Client Initiator

1. Install the Open-iSCSI initiator utilities.

#yum -y install iscsi-inititator-utils

2. Refer to the README file found at

https://github.com/mikechristie/open-iscsi

.

3. Configure your iSCSI array to allow access.

a. Examine

/etc/iscsi/initiatorname.iscsi

for the Linux host initiator name.

b. Update your volume manager with this host initiator name.

4. Set iscsi to start on boot.

#chkconfig iscscd on

#chkconfig iscsi on

5. Start iSCSI service (192.168.x.x is the IP Address of your target).

#iscsiadm -n discovery -t s -p 192.168.x.x

Observe the target names returned by iscsi discovery.

6. Log onto the target (-m XXX -T is XXX -l XXX -).

iscsiadm -m node -T iqn.2123-01.com:yada:yada: -p 192.168.2.124

-l

iSCSI Boot POST Setup

Intel® Ethernet iSCSI Boot features a setup menu which allows two network ports in one system to be
enabled as iSCSI Boot devices. To configure Intel® iSCSI Boot, power-on or reset the system and press the
Ctrl-D key when the message "

Press <Ctrl-D> to run setup...

" is displayed. After pressing the

Ctrl-D key, you will be taken to the Intel® iSCSI Boot Port Selection Setup Menu.

«
...
85
86
87
88
89
...
»

Содержание 10 Gigabit AT Ethernet Server Adapter






































































































































































Отзывы:

Нет отзывов