insys icom GPRS 5.1 Скачать руководство пользователя страница 89

Страница: 89 / 102

INSYS GPRS 5.1 serial

FAQ

FAQ

Problem:

Possible cause:

Remedy

The INSYS GPRS 5.1 serial
does not log in:

The location of the GSM
antenna is incorrect.

Check the signal quality of the GSM net-
work. For low field strength – below 12 –
the antenna location should be changed.

PIN incorrect

Use the HSComm to delete the PIN and to
enter the correct PIN.

The SIM card is blocked
because the PIN was en-
tered incorrectly three
times.

A PUK must be entered to enable the card.
Switch to the terminal program to enter
the PUK

and enter the following command:

AT+CPIN=<PUK>,<new PIN>

The SIM card is not ena-
bled.

Please contact the contact center of your
provider.

The power supply is not
sufficient.

Check the voltage supply using the in-
formation from Chapter 12 – Technical
Data.

No reaction to AT com-
mands.

The wrong interface has
been selected in the set-
tings for the serial inter-
face.

Check the interface settings

with the used COM port.

There is another program
running in the background
which accesses the same
serial interface.

Terminate all programs running in the
background.

Содержание GPRS 5.1







































































































Результаты поиска

Содержание GPRS 5.1

Отзывы:

insys icom GPRS 5.1, Руководство пользователя, Страница: 89 / 102

Результаты поиска

Содержание GPRS 5.1

Отзывы: