Instruo arbhar Скачать руководство пользователя страница 43

Страница: 43 / 50

Onset Triggered Modulation:

Summary: Onset Control Mode

is set to

delta

so that a gate signal will

generate from the

Gate Output

upon each onset detection. The

Gate

Output

triggers an envelope which is used to modulate the

Length

parameter of

arbhar.

Audio Path:

•

Connect any audio signal to the

Onset Input

•

Set the

Input Level

to a desired position and set the

Output Level

fully clockwise.

•

Set the

Dry/Wet Mix

knob to a desired position. If the

Dry/Wet

Mix

knob is fully clockwise (fully wet), then audio will not be heard

until audio has been captured.

•

Monitor

Output 1

for mono playback.

•

Set the

Sensitivity

parameter to its centre position.

•

Set the

Hold

parameters to its 10:00 position.

Gate Signal

Output

Audio Signal

Содержание arbhar



















































Результаты поиска

Содержание arbhar

Отзывы:

Похожие инструкции для arbhar

Бренды по названию

Популярные бренды

Instruo arbhar, Руководство пользователя

Результаты поиска

Содержание arbhar

Отзывы:

Похожие инструкции для arbhar

Бренды по названию

Популярные бренды