8/22/19 357-05181-02 Rev A © Inovonics, 2019 - www.inovonics.com
EN1216 Dual Input Universal with Wall
Tamper
Installation Instructions
1 Overview
The Inovonics EN1216 dual input universal with wall tamper is
designed to be used with any standard contact or sensor.
Inovonics multi-function add-on receivers will support both inputs
as separate devices.
The dual input universal with wall tamper is available in North
America, Australia and New Zealand; the radio frequency band
has been configured for the appropriate geographic area at the
factory.
Note:
The EN1216 requires use of a serial receiver or network
coordinator, as well as an application designed to support
advanced functionality.
1.1 Inovonics Contact Information
If you have any problems with this procedure, contact Inovonics
Wireless technical services:
• E-mail: [email protected].
• Phone: (800) 782-2709.
1.2 Dual Input with Wall Tamper Internal
Components
Figure 1
Dual input with wall tamper internal components
1.3 What’s In The Carton
• Two wall mount screws.
• Two wall mount anchors.
• Two selection jumpers.
• One 3.0V lithium battery.
2 Installation and Startup
2.1 Installation Notes
• These products are designed to be installed and maintained
by professional security technicians.
• Products are intended for indoor use.
• Manually test all products weekly.
2.2 Install the Battery
1.
Use your thumb to press the housing release tab on the
bottom of the transmitter; separate the housing.
2.
Install the battery.
3.
Press the reset button to initialize the transmitter.
2.3 Connect Input Wiring
The transmitter has a three-terminal contact block that can
connect inputs from one or two external contact loops. The
middle terminal is a ground, which is shared by both contact
loops. Input one can be configured for either a normally open or
a normally closed contact loop using the NO/NC selection pins;
input two is always normally closed.
1.
Connect wiring for the inputs you will be using.
2.
If you are not using input two, connect wiring between the
input terminal and the ground terminal to set it for normally
closed.
2.4 Select Input Type
The N/O-N/C selection pins allow the choice of a normally open
or normally closed state for the contact circuit wired to the input
one terminal.
The terminal is shipped set for normally closed, with no selection
jumper on the N/O selections pins.
1.
Place a selection jumper on the selection pins to select
normally open; remove the selection jumper from the
selection pins to select normally closed.
2.
Press the reset button to complete configuration.
2.5 Register the EN1216
Transmitters must be registered with the system in order to be
monitored and supervised. When supervised, the transmitter will
send a check-in message to the receiver every three minutes.
Each transmitter has a unique factory-programmed identification
number.
The EN1216 includes a back tamper switch. The tamper
condition must be defined within the control panel as a trouble
condition when the system is disarmed, and as an alarm
condition when the system is armed.
Refer to the receiver installation instructions for details on
registering a transmitter.
1.
When prompted by the receiver to reset transmitter, press
the reset button.
2.
Replace the cover.
Caution:
The dual input universal with wall tamper should be
tested after registration to ensure operation. To test the
transmitter, activate each of the conditions and ensure an
appropriate response.
2.6 Mount the EN1216
1.
Route the external wiring through the wall, as shown in
Figure 2.
2.
Mount the transmitter to the wall using the wall-mount screw
holes, ensuring the housing is flush against the wall and the
wall tamper switch is firmly depressed.
Figure 2
Mount the transmitter to the wall
3.
Close the housing.
4.
Secure the housing through the enclosed housing screw
hole. Accessing this screw on an active transmitter requires
opening the housing, causing a tamper condition.
For product and installation videos visit us at
www.inovonics.com/videos or use the QR
code below.
A
Wall-mount screw holes
B
N/O - N/C selection pins
C
Input one terminal
D
Ground terminal
E
Input two terminal
F
Reset button
G
Combined housing/wall tamper
switch
H
Housing closure screw hole
G
B
C
F
A
A
H
D
E
Wall Tamper
Switch