5.25.17 06287I © Inovonics, 2017 - www.inovonics.com
EE1941/EN1941/EN1941-60 One-Way Binary
RF Module
Installation and Operation Manual
1 Overview
EchoStream RF modules are designed to be easily interfaced with your
electronic remote application controller (RAC). RF modules allow the
assimilation of any user-specific application into an EchoStream system.
Once integrated with existing products, RF modules provide you with
complete EchoStream functionality.
One-way binary RF modules are end-devices that use a logic-level
connection to interface with your RAC. E*1941 one-way binary RF modules
can be used in either one-way or two-way EchoStream systems.
Figure 1
One-Way System Components
Note:
For UL 2560 installations, refer to the
EN6080 Area Control Gateway
Installation Instructions
or
EN6040-T Network Coordinator Installation Instructions
.
1.1 Maximum Number of Repeaters for a UL 2560
Installation
To achieve the 99.99% alarm message reliability required for UL 2560
compliance, system installations must operate within the following limits for
end device and repeater counts.
1.2
Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics Wireless
technical services:
• E-mail: [email protected].
• Phone: (800) 782-2709; (303) 939-9336.
1.3 Installation Notes
• These products are designed to be installed and maintained by
professional security technicians.
• Products are intended for indoor use.
• Manually test all products weekly.
2 One-Way Binary RF Module Components
The E*1941 is a universal one-way binary RF module with two alarm input
pins, allowing the use of dual inputs. Input one is the primary alarm, bit 0;
input two is the secondary alarm, bit 1.
There are two models in the E*1941 product family.
• The EN1941 and EN1941-60, for 900 MHz applications in North
America, New Zealand, and Australia.
• The EE1941, for 868 MHz applications in Europe.
Figure 2
One-Way Binary RF Module Components
Figure 3
EE1941 One-Way Binary RF Module Components
Frequency band selection pins (EN1941 and EN1941-60 only) Place a
jumper to select the frequency band for your geographic area.
• Place the jumper on the left two pins to select 915-928 MHz for
Australia.
• Place the jumper on the right two pins to select 921-928 MHz for New
Zealand.
• Leave the jumper off the pins to select 902-928 MHz for North
America.
ES selection pins (EE1941 only) To enable compatibility with ES products,
place a selection jumper on the ES selection pins; if no ES products are
used in your system, remove the selection jumper.
N/O selection pins Place a jumper to select normally open inputs; remove
the jumper to select normally closed.
End Devices
Maximum
Repeaters
150
397
250
386
350
375
500
360
1000
313
2000
238
3000
184
For product and installation videos visit us at
www.inovonics.com/videos or use the QR
code below.
A
Board stabilization hole.
B
Reserved
C
Reserved
D
Secondary alarm
E
Power
F
Ground
G
Primary alarm
H
LED contacts
I
Tamper input
J
Reset input
K
Frequency band
selection pins
L
N/O selection pins
M
Mounting hole
N
On-board antenna
O
Board stabilization
hole
A
Board stabilization hole.
B
Reserved
C
Reserved
D
Secondary alarm
E
Power
F
Ground
G
Primary alarm
H
LED contacts
I
Tamper input
J
Reset input
K
ES selection pins
L
N/O selection pins
M
Mounting hole
N
On-board antenna
O
Board stabilization
hole
B
C
G
D
I
J
E
F
K
L
M
N
H
A
O
B
C
G
D
I
J
E
F
K
L
M
N
H
A
O